- BEST HELICOOTER IN CLEARVIEW SIMULATOR TO LEARN ON UPDATE
- BEST HELICOOTER IN CLEARVIEW SIMULATOR TO LEARN ON FULL
Get close enough, press and diffuse bomb 1/5.īacktrack out through the blue shipping container and turn right. Your scanner will already have picked up the first bomb inside an open crate. Turn left and left again, around the back of the crates. The spray around the corner will still be present but can now be safely passed. It will start very slowly but should speed up as you go through 2 rotations and close the valve. Now move anti-clockwise to close the value. Similar to the bomb, move so the Robot Arm is close to the valve and press when the prompt appears. You will see a blue shipping container on the right which is open. Proceed forward, along the path to the right. Select the Scanner icon at the bottom of the screen and press to turn it on. Now hold to snip the wire.Ī door will open, so head outside. Press or so the cutting icon is highlighted in red. On this simple tutorial bomb, there is a single wire to cut. This takes you to the bomb diffusing screen. A notification will appear, so press to 'close up'. Immediately switch to the Robot Arm and lower it, until it gets close to the bomb in front of you. Grab them both then head back and start the mission. This time you need the Scanner and the Camera. You will once again start by heading to the Garage. Simply drive through to complete the mission, which will unlock: This will open the doorway behind the box. Press to switch back to arm control and hold to open the claws and drop the cube. Turn right and move so the arm and object are over the open box here. Once you grab the cube, press to switch back to robot control. If you accidentally knock the cube off, it’s best to reload the checkpoint, which is just after you pressed the third switch. This can be a little difficult to see – you can use to switch to the ‘arm-view’. Move the arm so the claws align with the cube and press to close the claws and grab it. Now press, which will open the claws on the arm. Drive near it and switch to arm control with. Your next task is to pick up the small cube on the metal block ahead. A panel will open up to the right of the 3rd switch. This time you have to raise the arm up higher to press the switch. The last switch is on the next wall, in between the control posters. Once again, the objective will update, this time to 2/3. If you drove close enough before switching you may be able to hit it, but otherwise press to drive the robot again and manoeuvre so you press the switch. Lower the arm so it is level with the lower switch. The arm controls are shown a little further, past the 2nd switch. The arm pivots at the base and half way along. Press to switch to change to arm control, then use. This one will be lower down on the wall, so you will have to move the arm.
BEST HELICOOTER IN CLEARVIEW SIMULATOR TO LEARN ON UPDATE
The objective in the top right will update to 1/3.Ĭontinue and you will immediately spot the next switch. The Robot Arm should already be at the right height by default – simply align the arm with the switch and drive forwards to press it. The first is immediately obvious on the left wall. In the next area you will need to press 3 switches.
BEST HELICOOTER IN CLEARVIEW SIMULATOR TO LEARN ON FULL
After a couple of corners, you will have to slalom around several fires, then time your progress through some flames that shoot out of pipes intermittently (these actually don’t cause too much damage so you can just keep going at full speed through the flames if you want). Proceed along the pathway once again it’s very linear. The tunnel turns back on itself – loop around to the right to continue. As it is the only equipment you have there is no need to use or to select the torch icon at the bottom of the screen. You’ll come to a wooden ramp – head over it and keep going straight to a darkened tunnel. Play around a little to get used to the robot’s movement if you want.įollow the linear path between the tyres. The bumpers will rotate you in place but I found they were useful for turning while in motion too. Press to cycle through the mission parameters or to skip them entirely. At the start of the mission, you will see a summary of what the mission entails in the form of a popup window. The first few missions are very quick, covering basic controls and actions. Go back to the main menu and you can now select Start to begin. You don't actually need to purchase the EOD and the only accessory available right now is the Torch so press to purchase it. The Garage should already be selected at the bottom-right, so head there. You're missing the Requirements: Robot EOD and Torchlight. Notice the red text under the mission description. When you load in for the first time, you'll see a short tutorial of the main menu.
MISSION 17: CHECKING CONTAMINATION IN FACTORY.
0 kommentar(er)
